 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PS200 Data Sheet PowerSmart(R) Configurable Battery Charger (c) 2005 Microchip Technology Inc. DS21891B Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, KEELOQ, MPLAB, PIC, PICmicro, PowerSmart and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. PowerCal, PowerInfo, PowerMate, PowerTool, Select Mode, Smart Serial and SmartTel are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. All other trademarks mentioned herein are property of their respective companies. (c) 2005, Microchip Technology Incorporated. Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. DS21891B-page ii (c) 2005 Microchip Technology Inc. PS200 PowerSmart(R) Configurable Battery Charger Features * User configurable battery charger. * Firmware available for the following cell chemistries: - Lithium Ion/Polymer (available now) - NiMH, NiCd (available Q2 2005) - Pb Acid (available Q3 2005) * 10-bit ADC for voltage, current and temperature measurement: - Accurate Voltage Regulation (+/-1%) - Accurate Current Regulation (+/-5%) * Maximum integration for optimal size: - Integrated voltage regulator - Internal 8 MHz clock oscillator - High-Frequency Switch mode charging - configurable switching frequency up to 1 MHz * 256 bytes EEPROM storage for charging parameters * Switch mode charger supports buck and synchronous buck topologies * Configurable charge status display via two LEDs * Power-on Reset (POR) * Brown-out Reset (BOR) * Power-saving Sleep mode Applications * * * * * * * * * Notebook Computers Personal Data Assistants Cellular Telephones Digital Still Cameras Camcorders Portable Audio Products Bluetooth(R) Devices Flashlights Power Tools Pin Diagram VDD LED2 VIN RESET CTRLOUT CHGOUT LOOPFBK LOOPIN CTRLIN LED1 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VSS TEMP VOVP SHDN CHGFBK BATID IFBOUT IFBINA IFBINB HVOUT 20-Pin PDIP, SOIC, SSOP (c) 2005 Microchip Technology Inc. PS200 DS21891B-page 1 PS200 Pinout Description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Pin Name VDD LED2 VIN RESET CTRLOUT CHGOUT LOOPFBK LOOPIN CTRLIN LED1 HVOUT IFBINB IFBINA IFBOUT BATID CHGFBK SHDN VOVP TEMP VSS Pin Type Input Type Output Type Supply O I I O O I I I O O I I O I I O I I Supply Power -- Analog ST -- -- Analog Analog Analog -- -- Analog Analog -- Analog Analog -- Analog Analog Power -- CMOS -- -- CMOS CMOS -- -- -- CMOS HVOD -- -- Analog -- -- Analog -- -- -- Supply voltage Status indicator Battery voltage input Reset PWM output for setting current level PWM output to a buck converter for charge control Current feedback loop Current feedback loop input Current level control Status indicator High-voltage, open-drain output pin (optional) Current feedback input pin B used for current scaling Current feedback input pin A used for current scaling Current feedback output Battery ID select Charge control feedback Shutdown signal, active-low Overvoltage protection Battery temperature input Supply ground Description Legend: I = Input, O = Output, ST = Schmitt Trigger Input Buffer, HVOD = High-Voltage Open-Drain DS21891B-page 2 (c) 2005 Microchip Technology Inc. PS200 1.0 PS200 OVERVIEW The following signals are outputs from this block: - IFBOUT - from op amp * Charge Control Module: - The charge control module generates a Pulse-Width Modulated signal called CHGOUT. Its frequency is configurable and can be set up to 1 MHz. This signal is connected to an external DC/DC buck converter. * Voltage Regulator - The integrated voltage regulator is designed to work with unregulated DC supplies. - There are guidelines that should be followed. A series limiting resistor (RVDD) should be placed between the unregulated supply and the VDD pin. The value for this series resistor (RVDD) must be between RMIN and RMAX as shown in the following equation: The PS200 is a configurable Switch mode charger which is comprised of a PIC16F microcontroller core and precision analog circuitry. This section explores the hardware features in relation to generic Switch mode charging. Subsequent sections will describe the operation of the PS200 with firmware for Lithium-based (Section 2.0 "Lithium Chemistry Algorithm"), Nickel-based (Section 3.0 "Nickel Chemistry Algorithm") and Lead Acid (Section 4.0 "Lead Acid Chemistry Algorithm") charging. * * * * * Oscillator Power-saving Sleep mode Power-on Reset (POR) Brown-out Reset (BOR) High-Endurance Flash/EEPROM Cell: - 100,000 write Flash endurance - 1,000,000 write EEPROM endurance - Flash/Data EEPROM retention: > 40 years High-Speed Comparator module with: - Two independent analog comparators Operational Amplifier module with two independent op amps Two-Phase Asynchronous Feedback PWM Voltage Regulator 10-bit (9-bit plus sign) A/D Converter In-Circuit Serial ProgrammingTM (ICSPTM) via two pins EQUATION 1-1: RMAX = Vs(MIN) - 5V) * 1000 1.05 * (16 mA + I(led)) Vs(MAX) - 5V) * 1000 .95 * (50 mA) * * * * * * RMIN = Where: RMAX = maximum value of series resistor (ohms) RMIN = minimum value of series resistor (ohms) Vs(MIN) = minimum value of charger DC supply (VDC) Vs(MAX) = maximum value of charger DC supply (VDC) I(led) = total current drawn by all LEDs when illuminated simultaneously The 1.05 and .95 constants are included to compensate for the tolerance of 5% resistors. The 16 mA constant is the anticipated load presented by the PS200, including the loading due to external components and a 4 mA minimum current for the shunt regulator itself. The 50 mA constant is the maximum acceptable current for the shunt regulator. 1.1 Hardware Features The PS200 features are well-suited for Switch mode battery charging. The PS200 device's block diagram (Figure 1-1) is to be used in conjunction with the Switch mode charger example (Figure 2-3, page 12). * Current/Voltage Measurement Block - The Current/Voltage Measurement Block consists of a 10-bit Analog-to-Digital converter, operational amplifiers and a comparator. The output of this block is fed into the Charge Control module. Please refer to Figure 1-1. The inputs into this block are to be connected as described in Figure 2-3. The following signals are inputs into this block: LOOPFBK - to comparator LOOPIN - to op amp and ADC CTRLIN - to op amp IFBINB - to op amp IFBINA - to op amp BATID - to ADC TEMP - to ADC CHGFBK - to comparator * The precision internal 8 MHz clock oscillator eliminates the need for external oscillator circuits. * In-circuit configurability utilizing 256 bytes of on-board EEPROM. * Power on Reset - The POR insures the proper start-up of the PS200 when voltage is applied to VDD. * Brown-out Reset - The BOR is activated when the input voltage falls to 2.1V; the PS200 is reset. (c) 2005 Microchip Technology Inc. DS21891B-page 3 PS200 FIGURE 1-1: PS200 BLOCK DIAGRAM RESET VDD VSS VOVP SHDN Voltage Regulator Voltage Reference - CTRLIN LOOPIN + OA1 - C1 + To Charge Control Module Internal Oscillator LOOPFBK CHGFBK IFBINB IFBINA IFBOUT VIN BATID TEMP Current/Voltage Measurement Block C2 + + OA2 - CTRLOUT Charge Control Module CHGOUT LED1 LED2 HVOUT 10-bit ADC DS21891B-page 4 (c) 2005 Microchip Technology Inc. PS200 2.0 LITHIUM CHEMISTRY ALGORITHM 2.1.2 USER CONFIGURABLE PARAMETERS The PS200 supports user configurable parameters that allow for customizing the charging profile. This feature allows for the maximum reuse of hardware, thus reducing time-to-market. These parameters include: * Battery Temperature: - Minimum/maximum temperature for charge initiation - Maximum temperature allowed during charge * Battery Voltage: - Minimum/maximum voltage for charge initiation - Target voltage during Voltage Regulation - Voltage at which the charger will restart charging after completion of a valid charge cycle * Charge Current: - Target current during Current Regulation - Taper current threshold for End-Of-Charge during Voltage Regulation - Target current during Precharge * Time: - Precharge time limit - Current Regulation time limit - Voltage Regulation time limit * Status Display: - Two LEDs denote the charge states. Their flash rates can be modified. The PS200 provides an unprecedented level of configurability for charging Lithium Ion/Lithium Polymer battery packs. It's precision, 10-bit Analog-to-Digital converter and high-frequency Pulse-Width Modulator enable the PS200 to provide optimum control of charging algorithms for lithium battery chemistries. Special features include an internal voltage regulator and an internal clock oscillator that reduce external component count. 2.1 2.1.1 Lithium Overview MULTI-STEP CHARGING To ensure the proper treatment of lithium chemistries during extreme temperature and voltage conditions, multi-step charging is required. The PS200 starts the charging cycle upon sensing the presence of a battery pack and a valid charging supply. During charge qualification, the battery's temperature and voltage are measured to determine the appropriate initial state. The initial states include Charge Suspend, Precharge and Current Regulation. Charge Suspend halts charging when the user defined preset conditions for charging are not met. Precharge allows for the recovery of deeply discharged batteries by applying a low-charge current. Current Regulation provides constant current, voltage limited charge. Upon reaching the target voltage during Current Regulation, the Voltage Regulation state is entered. Charging continues at a constant voltage until the current decreases to the user specified minimum current threshold (VRIMin). At this threshold, charging is terminated and the End-Of-Charge state is reached. The state diagram illustrates the charging cycle (see Figure 2-1). (c) 2005 Microchip Technology Inc. DS21891B-page 5 PS200 FIGURE 2-1: PS200 STATE DIAGRAM LI CHARGER (A) Charge Pending (1) VCC Reset or BATPRES = 0 (4) BATPRES = 1 (2) Vcc Reset or BATPRES = 0 (3) VCC Reset or BATPRES = 0 (6) V > VMIN and TMAX > T > TMIN (5) V> VRCHG (B) Charge Qualification (7) TMAX < T OR T < TMIN (9) TMAX > T > TMIN and V < VRCHG (C) Charge Suspend (10) t > tp and V < VMIN or T > TMAX or T < TMIN (8) V < VMIN and TMAX > T > TMIN (D) Precharge (11) V > VMIN and TMAX > T > TMIN (E) Current Regulation (12) V > VMAX or T > TMAX or t > ti or T < TMIN (14) V > VREG, T < TMAXCHG (13) VCC Reset or BATPRES = 0 (F) Voltage Regulation (15) V > VMAX or T > TMAXCHG or t > tv (16) VCC Reset BATPRES = 0 (17) I < IMIN and V VREG (18) BATPRES = 0 or V < VRCHG or VCC Reset Legend: T TMIN TMAX TMAXCHG V VMIN VMAX VREG VRCHG Note: (G) Charge Complete = = = = = = = = = battery temperature minimum temperature allowed during charging maximum temperature allowed during charging maximum temperature allowed during voltage regulation battery voltage minimum voltage for entering current regulation maximum voltage for charge initiation target voltage during charge regulation voltage threshold at which charging will restart = charge current = taper current threshold for End-Of-Charge during voltage regulation t = time tp = precharge time limit ti = current regulation time limit tv = voltage current time limit BATPRES= battery present variable; if `1', then battery is present; if `0', then battery is not present I IMIN When the PS200 resets, it enters the Charge Pending state. DS21891B-page 6 (c) 2005 Microchip Technology Inc. PS200 2.2 Lithium Charging 2.2.3 PRECHARGE STATE To ensure the proper treatment of lithium chemistries during extreme temperature and voltage conditions, multi-step charging is required. The PS200 measures key voltage, temperature and time parameters. It compares them to user defined voltage, temperature and time limits. These limits are described in Section 2.4 "Lithium Configurable Parameters". Note: Refer to Figure 2-1 and Figure 2-2 for clarification when reading this section. The Precharge state allows for the recovery of a deeply discharged battery pack by applying a low charge rate. In this state, a user configured precharge current is applied to the battery, resulting in an increase in the battery's voltage (refer to Figure 2-2). There are three possible next states (see Figure 2-1). 1. If the battery's voltage is above the minimum voltage for charge initiation (VMIN) and the battery's temperature is within the limits for charge initiation (TMAX, TMIN), then the next state is Current Regulation (E). If the Precharge state time limit is exceeded (tp) and the battery's voltage remains less than the minimum voltage for charge initiation (VMIN), then the next state is Charge Suspend (C). If the Precharge state time limit is exceeded (tp) and the battery's temperature is greater than the maximum temperature for charge initiation (TMAX), then the next state is Charge Suspend (C). If the Precharge state time limit is exceeded (tp) and the battery's temperature is less than the minimum temperature for charge initiation (TMIN), then the next state is Charge Suspend (C). 3. If the battery pack is taken away (BATPRES = 0), then the PS200 enters the Charge Pending (A) state. 2.2.1 CHARGE PENDING STATE - BEGINNING THE CHARGE CYCLE 2. The PS200 is initially set in the Charge Pending state (A). In this state, the presence of a battery pack must be sensed in order to begin the charging cycle. The PS200 comes up in the Charge Pending state, after a Reset, independent of the previous state. 2.2.2 CHARGE QUALIFICATION STATE During charge qualification, the battery's temperature and voltage are measured to determine the next charging state. There are four possible next states (see Figure 2-1). 1. If the battery's temperature is outside of the limits for charge initiation (TMAX, TMIN) then the next state is Charge Suspend (C). If the battery's voltage is less than the minimum voltage for charge initiation (VMIN) and its temperature is within the limits for charge initiation (TMAX, TMIN), then the next state is Precharge (D). If the battery's voltage is above the minimum voltage for charge initiation (VMIN) and its temperature is within the limits for charge initiation (TMAX, TMIN), then the next state is Current Regulation (E). If the battery's voltage is above the voltage at which charging will restart (VRCHG), then the next state is Charge Complete (G). 2. 2.2.4 CHARGE SUSPEND STATE In the Charge Suspend state, no current is applied to the battery pack. There are two possible next states (see Figure 2-1). 1. If the battery's temperature is within the limits for charge initiation (TMAX, TMIN) and its voltage is less than the voltage at which charging would restart (VRCHG), then the next state is Precharge (D). If the battery pack is taken away (BATPRES = 0), then the PS200 enters the Charge Pending (A) state. 3. 4. 2. (c) 2005 Microchip Technology Inc. DS21891B-page 7 PS200 2.2.5 CURRENT REGULATION STATE 2.2.6 VOLTAGE REGULATION STATE The Current Regulation state can be entered from the Precharge state or Charge Qualification state. Battery charging is initiated. This state provides constant current, voltage limited charging (refer to Figure 2-2). The charge current is referred to as IREG or the regulation current. While the current is applied, the battery's voltage increases until it reaches a voltage limit referred to as VREG or regulation voltage. Charging continues, during which battery voltage and temperature are monitored. There are three possible next states. 1. If the battery's voltage reaches or exceeds the voltage limit, VREG and its temperature remains below the maximum allowable during current regulated charging (TMAXCHG), then the next state is Voltage Regulation (F). If the battery exhibits any one of the following conditions then the next state is Charge Suspend (C): - Battery voltage exceeds upper voltage limit for charging (VMAX) - Battery temperature exceeds upper temperature limit for charging (TMAX) - Battery temperature is below the lower temperature limit for charging (TMIN) If the time in the Current Regulation state exceeds the time limit (ti), then the next state is Charge Suspend (C). 3. If the battery pack is taken away (BATPRES = 0), then the PS200 enters the Charge Pending (A) state. Voltage Regulation provides charging at a constant voltage while the charge current decreases (or tapers) to the user specified minimum current threshold (IMIN). There are three possible next states. 1. When the charge current reaches the taper current threshold for End-Of-Charge (IMIN) and the battery's voltage remains at the regulated voltage value (VREG), then the battery has reached the Charge Complete (G) state. If the battery exhibits any one of the following conditions, then the next state is Charge Suspend (C). - Battery voltage exceeds upper voltage limit for charging (VMAX) - Battery temperature exceeds upper temperature limit for charging (TMAXCHG) If the time in the Voltage Regulation state exceeds the time limit (tv), then the next state is Charge Suspend (C). If the battery pack is taken away (BATPRES = 0), then the PS200 enters the Charge Pending (A) state. 2. 2. 3. 2.2.7 CHARGE CYCLE COMPLETE STATE The user specified minimum current threshold (IMIN) can be configured for various charging temperatures. At this threshold, charging is terminated and the EndOf-Charge state is reached. The PS200 can renew the charge cycle by entering the Charge Pending (A) state when: 1) the battery is removed (BATPRES = 0), or 2) if the battery's voltage falls below the recharge threshold voltage (VRCHG). FIGURE 2-2: PS200 CHARGING PROFILE VREG Battery Voltage Current Voltage Regulation Current Regulation Precharge IMIN Charge Current Time DS21891B-page 8 (c) 2005 Microchip Technology Inc. Voltage IREG PS200 2.3 KEELOQ(R) Algorithm 2.4.2.2 Current Regulation Parameters The PS200 includes Microchip's KEELOQ decoder algorithm. The KEELOQ code hopping technology is a worldwide standard providing a simple, yet highly secure, solution for authentication. Microchip's battery management products include the KEELOQ algorithm to provide secure identification for rechargeable batteries. When the KEELOQ algorithm is enabled, the PS200 will issue a 32-bit challenge to the attached rechargeable battery. The battery, which also includes the KEELOQ decoder algorithm, will generate a response. See Microchip application note AN827 "Using KEELOQ(R) to Validate Subsystem Compatibility" (DS00827) for details on implementing a complete KEELOQ battery authentication system. The Current Regulation parameters configure the charger's operation during this second battery charging phase. 2.4.2.3 Voltage Regulation Parameters The Voltage Regulation parameters configure the charger's operation during this third battery charging phase. 2.4.3 LED DISPLAY CONFIGURATION The PS200 supports a two-LED charging state display. These LEDs can be configured to identify seven unique charger states: * Charge Pending - charger is waiting for battery pack that needs charge. * Charge Qualification - charger is determining if the battery pack can be safely charged. * Precharge - charger is charging the battery pack under the conditions configured for precharge. * Charge Suspend - charger has temporarily suspended charging the battery pack. This state is usually entered as a result of violating a maximum temperature requirement. Charging will resume when conditions are within required charging parameter values. * Current Regulation - charger is charging the battery pack with a constant current. * Voltage Regulation - charger is charging the battery pack at the constant target voltage. * Charge Complete - charger has completed charging the battery pack. 2.4 Lithium Configurable Parameters The PS200 device's configurable parameters allow for flexible changes in designing battery chargers. The parameters are categorized as follows: * Configuration * Charging Limits - Precharge - Current Regulation - Voltage Regulation * LED Display Configuration Please refer to Table 2-1 "PS200 Lithium Configurable Parameters". 2.4.1 CONFIGURATION PARAMETERS The configuration parameters provide an identity to the battery pack and provide its basic characteristics to the PS200. 2.4.2 2.4.2.1 CHARGING LIMITS Precharge Parameters The Precharge parameters configure the charger's operation during this initial battery charging phase. (c) 2005 Microchip Technology Inc. DS21891B-page 9 PS200 TABLE 2-1: PS200 LITHIUM CONFIGURABLE PARAMETERS # Lower Upper Bytes Limit Limit -- -- 1 2 1 N/A N/A 1 0 7 N/A N/A 255 65535 83 Typical Value Microchip PS200 4 2000 15 Typical Value 2500 3000 200 50 ASCII value. ASCII value. Number of series connected cells in the battery pack. Full-charge capacity of the battery pack. LUT value which determines the PWM frequency. Step 1 - Configuration Parameter Name MfgName DevName SeriesCells Capacity (mAh) PWMFreq Description Step 2 - Charging Limits Parameter Name PCVMin (mV) PCVMax (mV) PCCurrent (mA) PCTempMin # Lower Upper Bytes Limit Limit 2 2 2 1 0 0 0 0 65535 65535 65535 255 Description Minimum cell voltage required to enable charging with precharge conditions. Maximum cell voltage required to enable charging with precharge conditions. Charging current during precharge. Minimum temperature required to enable charging with precharge conditions. PCTempMin value = (temperature C * 10 + 200)/4; so typical value of 50 = 0C. Maximum temperature required to enable charging with precharge conditions. PCTempMax value = (temperature C * 10 + 200)/4; so typical value of 175 = 50C. Duration of precharge. Target cell voltage in current regulation. This is set to the fully charged voltage of one cell, typically, as specified by the cell manufacturer. Charging current during current regulation. Current regulation time limit. Voltage regulation recharge cell voltage. Charger will automatically begin charging if cell voltage of pack falls below SeriesCells * VRVrech. Voltage regulation fully charged current. This is the value of the taper current or IMIN which will determine that the battery is fully charged. Voltage regulation time limit. Maximum temperature required to enable charging during current regulation and voltage regulation. TempMax value = (temperature C * 10 + 200)/4; so typical value of 200 = 60C. PCTempMax 1 0 255 175 PCTime (min) CRVTarg (mV) 1 2 0 0 255 65535 60 4200 CRCurrent (mA) CRTimeMax (min) VRVrech (mV) 2 1 2 0 0 0 65536 255 65536 2000 90 3780 VRIMin (mA) 2 0 65536 150 VRTimeMax (min) TempMax 1 1 0 0 255 255 90 200 DS21891B-page 10 (c) 2005 Microchip Technology Inc. PS200 TABLE 2-1: PS200 LITHIUM CONFIGURABLE PARAMETERS (CONTINUED) # Lower Upper Bytes Limit Limit 1 1 1 1 1 1 1 1 1 1 1 1 1 1 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Typical Value Step 3 - LED Display Parameter Name LED1Pending LED2Pending LED1Qual LED2Qual LED1PC LED2PC LED1Suspend LED2Suspend LED1CR LED2CR LED1VR LED2VR LED1Full LED2Full Miscellaneous Parameter Name PatternID BatIDMin BatIDMax # Lower Upper Bytes Limit Limit 2 1 1 0x0 0 0 0xFFFF 255 255 Typical Value 0x0 0 255 Pattern ID. BATID input pin value minimum. BATID input pin value maximum. Description Description 0b00000000 LED1 display when charge is pending. 0b00000000 LED2 display when charge is pending. 0b00000000 LED1 display during charge qualification. 0b00000000 LED2 display during charge qualification. 0b00000000 LED1 display during precharge. 0b00000000 LED2 display during precharge. 0b00000000 LED1 display when charge has been temporarily suspended. 0b00000000 LED2 display when charge has been temporarily suspended. 0b00000000 LED1 display during charge regulation. 0b00000000 LED2 display during charge regulation. 0b00000000 LED1 display during voltage regulation. 0b00000000 LED2 display during voltage regulation. 0b00000000 LED1 display when battery is fully charged. 0b00000000 LED2 display when battery is fully charged. (c) 2005 Microchip Technology Inc. DS21891B-page 11 2.5 FIGURE 2-3: PS200 17 18 Lithium Application C18 4.7 F 3 IF SUPPLY VOLTAGE EXCEEDS VGS RATING OF Q1, A ZENER DIODE CAN BE PLACED IN SERIES WITH THE DRAIN OF Q4, TO LIMIT VGS OF Q1 TO A SAFE LEVEL. SHDN 1-WIRE COMM. ACCESS LED1 LED2 VREF CP1 HVOUT 11 VOVP 10 T/ID 2 TP TN VIN 19 1 2 3 Rt/Ct/D6 PWM RAMP GENERATOR. RD1 1N4148 1.0M Rt R20 10.0K 5 6 7 8 Q7 MMBT4401 CP2 3 C1 100 nF 2 PWM 5 6 7 8 VDD Q4 2N7002 CP + VDD L1 Q3 Cout RSENSE + 4 20 VSS PH2 CTRLOUT CTRLIN IFBINB + OP2 IFBINA 1.00K OP2 IS CURRENT SENSE AMP. RIH, RIL, RSENSE DETERMINE CURRENT SIGNAL SCALING. CIH IS USED IN SOME APPLICATIONS TO FILTER NOISE/SPIKES FROM CURRENT SENSE SIGNAL. RIL 13 12 Rt/Ct/D6 CONVERT PWM OUTPUT TO RAMP WAVEFORM, WHICH IS FED BACK TO CP2 AND COMPARED TO ERROR AMP SIGNAL TO DETERMINE PWM DUTY CYCLE. Figure 2-3 is an example of the PS200 in a synchronous buck charger for Lithium Ion batteries. The sense resistor (RSENSE) is in a low side configuration. CHGFBK 6 CIN/COUT/L1/Q1/Q2: SYNCHRONOUS-BUCK POWER SECTION 16 Q2 1 2 3 FIRMWARE CURRENT CONTROL OUTPUT: R5 10.0K 5 9 OP1 LOOPIN 14 IFBOUT 8 R1 10.0K C9 470 nF LOOPFBK R12 10.0K Ct Q8 RG2 MMBT4403 R11 1.5K 1 SHDN 1 R5/R9/C9 FORM A LOW-PASS FILTER, WITH A TIME CONSTANT OF 4.7 MILLISECONDS. THIS ALLOWS FIRMWARE LOOP UPDATE RATES OF UP TO 50 TIMES A SECOND. CCOMP1 7 DS21891B-page 12 REDLED GRNLED + SP POWER SUPPLY INPUT 4.7 F SUPPLY MUST BE FUSED OR CURRENT LIMITED C23 SN RVDD: POWER SUPPLY DROPPING RESISTOR - FOR REVISION HISTORY, SEE 826216 CHANGE LOG OVP DIVIDER VIN DIVIDER RVDD ROVP DISCRETE MOSFET DRIVERS: RGx/RD1 VALUES ARE DEPENDENT UPON CHARACTERISTICS OF Q1 AND Q2 ROVL C3 100 nF THERMISTOR/ID CONNECTIONS R19 10.0K RVL RVH R2 1.5K R10 1.5K DATA MCLR + R4 4 RESET D6 BAT54 D5 PH1 4 15 COMG U1 PS200 RG1 Q1 MMBT4401 Q6 Q3 -- REVERSE CONDUCTION BLOCKING SWITCH CIN CHARGER OUTPUT (TO BATTERY) CN - CTRLOUT IS COMPARE OUTPUT, WHICH IS A FIRMWARE CONTROLLED PWM THAT SETS CURRENT LEVEL. R5/R9/C9 SCALE AND FILTER THE VOLTAGE FROM CTRLOUT, FOR APPLICATION TO OP1. R9 10.0K Q1 IS A P-CHANNEL MOSFET, SELECTED FOR AN OPTIMUM BALANCE BETWEEN SWITCHING SPEED AND LOW Rdson. RIH Q2 IS AN N-CHANNEL, LOGIC LEVEL DRIVE (VGS = 5V) MOSFET, WITH AN INTEGRATED SCHOTTKY DIODE. Q1 IS SELECTED FOR LOW Rdson, TO MINIMIZE CONDUCTION LOSSES (SEPARATE MOSFET AND SCHOTTKY DEVICES CAN ALSO BE USED). R8 10.0K RCOMP CIH CCOMP2 SWITCH MODE CHARGER CIRCUIT EXAMPLE HARDWARE FEEDBACK TO PWM: OP1 IS ERROR AMP. CCOMP1/CCOMP2/RCOMP ARE LOOP COMPENSATION COMPONENTS. COMPONENTS THAT DO NOT HAVE A NUMERICAL VALUE ASSOCIATED WITH THEM ARE DEPENDENT UPON THE VOLTAGE/CURRENT SPECIFICATIONS OF THE PARTICULAR APPLICATION. CONSULT MICROCHIP FOR GUIDANCE IN DEFINING THESE COMPONENT VALUES. PS200-BASED CHARGER REFERENCE DESIGN - SYNCHRONOUS BUCK TOPOLOGY THIS DESIGN IS A DUAL LOOP TOPOLOGY, WITH HARDWARE-BASED CURRENT FEEDBACK CONTROL AND FIRMWARE-BASED VOLTAGE FEEDBACK CONTROL. > HARDWARE CONFIGURED AS A CONSTANT-CURRENT LOOP, CONTROLLING PWM. > FIRMWARE SETS CURRENT LEVEL BY ADJUSTING PWM SIGNAL AT CTRLOUT. > FIRMWARE ALSO CONSTANTLY MEASURES VOLTAGE; WHEN VOLTAGE SETPOINT REACHED, FIRMWARE DYNAMICALLY ADJUSTS CURRENT TO MAINTAIN CONSTANT VOLTAGE. Refer to the Microchip web site (www.microchip.com) for the latest Application Notes that reference this theory of operation and component values. (c) 2005 Microchip Technology Inc. PS200 3.0 NICKEL CHEMISTRY ALGORITHM 4.0 LEAD ACID CHEMISTRY ALGORITHM The PS200 algorithms for NiMH and NiCd chemistries are currently being developed. The PS200 algorithms for lead acid chemistries are currently being developed. (c) 2005 Microchip Technology Inc. DS21891B-page 13 PS200 NOTES: DS21891B-page 14 (c) 2005 Microchip Technology Inc. PS200 5.0 ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings Ambient temperature under bias................................................................................................................. -40 to +125C Storage temperature .............................................................................................................................. -65C to +150C Voltage on VDD with respect to VSS ............................................................................................................ -0.3 to +6.5V Voltage on RESET with respect to Vss ......................................................................................................-0.3 to +13.5V Voltage on HVOUT with respect to Vss ........................................................................................................... 0V to +8.5V Voltage on all other pins with respect to VSS ................................................................................. -0.3V to (VDD + 0.3V) Total power dissipation(1) .....................................................................................................................................800 mW Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin ..............................................................................................................................250 mA Input clamp current, IIK (VI < 0 or VI > VDD)...................................................................................................................... 20 mA Output clamp current, IOK (Vo < 0 or Vo >VDD)................................................................................................................ 20 mA Maximum output current sunk by any I/O pin...................................................................................................... 25 mA(2) Maximum output current sourced by each Port .................................................................................................. 50 mA(2) Note 1: Power dissipation is calculated as follows: PDIS = VDD x {IDD - IOH} + {(VDD - VOH) x IOH} + (VOL x IOL). 2: Total source current must not exceed the shunt regulator capacity. NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 5.1 ESD: Reliability Targets 4000V HBM 400V MM all pins including VDD, VSS, RESET The device must be designed to target the following reliability specifications: Latch-up: 400 mA @ 125C 5.2 Design Targets The AC/DC specifications included in the following sections are preliminary specifications that we intend to publish at product introduction. As the product matures, we intend to expand the specifications. Therefore, design should try and meet the following extended VDD/temperature targets: 1. 2. Frequency of operation: DC - 4 MHz, VDD = 2.0V - 5.5V, -40C to 125C Frequency of operation: DC - 20 MHz, VDD = 4.5V - 5.5V, -40C to 125C (c) 2005 Microchip Technology Inc. DS21891B-page 15 PS200 5.3 DC Characteristics Standard Operating Conditions (unless otherwise stated) Operating temperature -40C to +85C Characteristic Supply Voltage RAM Data Retention Voltage(1) VDD Start Voltage to ensure internal Power-on Reset signal Min 2.0 4.5 1.5* -- Typ -- -- -- VSS -- 2.1 -- 2.9 Max 5.0 5.0 -- -- -- -- -- TBD Units V V V V Conditions FOSC <= 4 MHz FOSC > 4 MHz Device in Sleep mode See section on Power-on Reset for details DC CHARACTERISTICS Param No. D001B D001C D002 D003 D004 D005 D010S D020 Sym VDD VDR VPOR SVDD VBOR IDD IPD VDD Rise Rate to ensure internal 0.05* Power-on Reset signal VDD Voltage required to initiate a Brown-out Detect Supply Current(2) Power-Down Current(3) -- -- -- V/ms See section on Power-on Reset for details V mA nA VDD and current are constant due to shunt regulator. VDD = 5.0V, WDT disabled Legend: TBD = To Be Determined * These parameters are characterized but not tested. Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested Note 1: This is the limit to which VDD can be lowered in Sleep mode without losing RAM data. 2: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to VDD; RESET = VDD. 3: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD and VSS. 5.4 Shunt Regulator SHUNT REGULATOR SPECIFICATIONS Standard Operating Conditions (unless otherwise stated) Operating temperature -40C to +125C Sym VSHUNT ISHUNT RSHUNT TSETTLE CLOAD ISNT Min 4.75 4 -- -- 0.01 -- Typ -- -- -- -- -- 180 Max 5.25 50 3 150 10 -- Units Volts mA ns F A To 1% of final value Bypass capacitor on VDD pin Includes band gap reference current Comments TABLE 5-1: Shunt Regulator Specifications Characteristic Shunt Voltage Shunt Current Shunt Resistance Settling Time* Load Capacitance Regulator Operating Current * Note: These parameters are characterized but not tested. The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. DS21891B-page 16 (c) 2005 Microchip Technology Inc. PS200 5.5 DC Characteristics Standard Operating Conditions (unless otherwise stated) Operating temperature -40C to +85C Characteristic Input Low Voltage RESET VIH D042 IIL D060A D061 D080 VOL Input High Voltage RESET Input Leakage Current(2) Analog inputs RESET(1) Output Low Voltage Pins LED1, LED2, CTRLOUT, CHGOUT, HVOUT Output High Voltage D090 VOH Pins LED1, LED2, CTRLOUT, CHGOUT, HVOUT VDD - 0.7 -- -- V IOH = -3.0 mA, VDD = 4.5V -- -- 0.6 V IOL = 8.5 mA, VDD = 4.5V -- -- 0.1 1 1 5 A A Vss VPIN VDD Vss VPIN VDD 0.8 VDD -- VDD V 4.5V VDD 5.5V, otherwise entire range VSS -- 0.2 VDD V 4.5V VDD 5.5V, otherwise entire range Min Typ Max Units Conditions DC CHARACTERISTICS Param No. Sym VIL D032 Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: The leakage current on the RESET pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 2: Negative current is defined as current sourced by the pin. 5.6 DC Characteristics Standard Operating Conditions (unless otherwise stated) Operating temperature -40C to +85C Characteristic Capacitive Loading Specs on Output Pins Min Typ Max Units Conditions DC CHARACTERISTICS Param No. Sym D101 CIO Pins LED1, LED2, CTRLOUT, CHGOUT, HVOUT Data EEPROM Memory Endurance VDD for read/write Erase/Write cycle time -- -- 50* pF D120 D121 D122 ED VDRW TDEW 1M VMIN -- 10M -- 5 -- 5.5 6 E/W 25C at 5V V ms VMIN = Minimum operating voltage * These parameters are characterized but not tested. Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. (c) 2005 Microchip Technology Inc. DS21891B-page 17 PS200 5.7 AC Characteristics: PS200 (Industrial) EXTERNAL CLOCK TIMING Q4 Q1 Q2 Q3 Q4 Q1 FIGURE 5-1: FOSC 1 2 3 3 4 4 TABLE 5-2: Param No. Sym FOSC 1 TOSC EXTERNAL CLOCK TIMING REQUIREMENTS Characteristic Oscillator Frequency(1) Oscillator Period(1) Min -- -- Typ 8 125 Max -- -- Units MHz ns Conditions Using PS200 internal oscillator Using PS200 internal oscillator Data in "Typ" column is at 5 V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS21891B-page 18 (c) 2005 Microchip Technology Inc. PS200 FIGURE 5-2: CLKO AND I/O TIMING Q4 FOSC 10 13 19 14 LED1, LED2, CTRLOUT, CHGOUT, HVOUT (input) LED1, LED2, CTRLOUT, CHGOUT, HVOUT (output) 18 11 22 23 12 16 Q1 Q2 Q3 17 Old Value 20, 21 15 New Value TABLE 5-3: Param No. 17 18 19 20 21 CLKO AND I/O TIMING REQUIREMENTS Sym TosH2ioV TosH2ioI Characteristic FOSC (Q1 cycle) to Port Out Valid FOSC (Q2 cycle) to Port Input Invalid (I/O in hold time) Min -- -- 100 0 -- -- Typ 50 -- -- -- 10 10 Max 150* 300 -- -- 40 40 Units ns ns ns ns ns ns Conditions TioV2osH Port Input Valid to FOSC (I/O in setup time) TioR TioF Port Output Rise Time Port Output Fall Time * These parameters are characterized but not tested. Data in "Typ" column is at 5.0 V, 25C unless otherwise stated. (c) 2005 Microchip Technology Inc. DS21891B-page 19 PS200 FIGURE 5-3: VDD RESET Internal POR 33 PWRT Time-out 32 30 RESET AND POWER-UP TIMER TIMING Internal Reset 34 LED1, LED2, CTRLOUT, CHGOUT, HVOUT (input) FIGURE 5-4: BROWN-OUT DETECT TIMING AND CHARACTERISTICS VDD BVDD BVHY BVDD + BVHY 35 Reset (due to BOR) (Device not in Brown-out Detect) (Device in Brown-out Detect) 64 ms Time-out (if PWRTE) DS21891B-page 20 (c) 2005 Microchip Technology Inc. PS200 TABLE 5-4: Param No. 30 32 33* 34 RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER AND BROWN-OUT DETECT REQUIREMENTS Characteristic RESET Pulse Width (low) Oscillation Start-up Timer Period Power-up Timer Period (4 x TWDT) I/O High-Impedance from RESET Low or Watchdog Timer Reset Brown-out Detect Voltage Brown-out Hysteresis Brown-out Detect Pulse Width 100* Min 2 11 -- 28* TBD -- 2.025 25 -- -- Typ -- 18 1024 TOSC 64 TBD -- Max Units -- 24 -- 132* TBD 2.0 2.175 s ms -- ms ms s V mV s VDD BVDD (D005) Conditions VDD = 5V, -40C to +85C Extended temperature TOSC = FOSC period VDD = 5V, -40C to +85C Sym TMCL TOST TPWRT TIOZ BVDD BVHY 35 TBOR Legend: TBD = To Be Determined * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. TABLE 5-5: Param No. F10 Sym FOSC PRECISION INTERNAL OSCILLATOR PARAMETERS Characteristic Internal Calibrated INTOSC Frequency(1) Freq Min Tolerance 1% 2% 5% -- -- -- Typ 8.00 8.00 8.00 Max TBD TBD TBD Units Conditions MHz VDD and Temperature (TBD) MHz 2.5V VDD 5.5V 0C TA +85C MHz 2.0V VDD 5.5V -40C TA +85C (Ind.) -40C TA +125C (Ext.) s s s VDD = 2.0V, -40C to +85C VDD = 3.0V, -40C to +85C VDD = 5.0V, -40C to +85C F14 TIOSCST Oscillator Wake-up from Sleep Start-up Time* -- -- -- -- -- -- TBD TBD TBD TBD TBD TBD Legend: TBD = To Be Determined Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: To ensure these oscillator frequency tolerances, VDD and VSS must be capacitively decoupled as close to the device as possible. 0.1 F and .01 F values in parallel are recommended. (c) 2005 Microchip Technology Inc. DS21891B-page 21 PS200 FIGURE 5-5: CTRLOUT TIMINGS (PIN 5) CTRLOUT TABLE 5-6: Param No. 53* 54* Sym TccR TccF CTRLOUT REQUIREMENTS Characteristic CTRLOUT Output Rise Time CTRLOUT Output Fall Time Min -- -- Typ 25 25 Max Units 50 45 ns ns Conditions * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. Parameters are for design guidance only and are not tested. DS21891B-page 22 (c) 2005 Microchip Technology Inc. PS200 5.8 Current Voltage Measurement Block DC CHARACTERISTICS (PINS LOOPIN, CTRLIN, IFBINB, IFBINA INPUTS; PIN IFBOUT OUTPUT) Standard Operating Conditions (unless otherwise stated) VDD = 2.7V to 5.5V, TA = 25C, VCM = VDD/2, RL = 100 k to VDD/2 and VOUT ~ VDD/2 Operating Temperature -40C to +85C for Industrial Parameters Input Offset Voltage Input Current and Impedance Input Bias Current Input Offset Bias Current Common Mode Common Mode Input Range Common Mode Rejection Open-Loop Gain DC Open-Loop Gain DC Open-Loop Gain Output Output Voltage Swing Output Short Circuit Current Power Supply Power Supply Rejection Min -- -- -- VSS TBD -- -- VSS + 50 -- 80 Typ 5 2* 1* -- 70 90 60 -- 25 -- Max -- -- -- VDD - 1.4 -- -- -- VDD - 50 TBD -- Units mV nA pA V dB dB dB mV mA dB VDD = 5V VCM = VDD/2, Frequency = DC No load Standard load TO VDD/2 (20 k connected to VDD, 20 k + 20 pF to VSS) Conditions TABLE 5-7: DC CHARACTERISTICS Param Sym No. 001 002 003 004 005 006A 006B 007 008 010 VOS IB IOS VCM CMR AOL AOL VOUT ISC PSR Legend: TBD = To Be Determined * These parameters are characterized but not tested. TABLE 5-8: AC CHARACTERISTICS (PINS LOOPIN, CTRLIN, IFBINB, IFBINA INPUTS; PIN IFBOUT OUTPUT) Standard Operating Conditions (unless otherwise stated) VDD = 2.7V to 5.5V, VSS = GND, TA = 25C, VCM = VDD/2, RL = 100 k to VDD/2 and VOUT = VDD/2 Operating Temperature -40C to +85C for Industrial Parameters Gain Bandwidth Product Turn-on Time Phase Margin Slew Rate Min -- -- -- 2 Typ 3 10 60 TBD Max -- TBD -- -- Units MHz s V/s VDD = 5V VDD = 5V VDD = 5V Conditions AC CHARACTERISTICS Param No. 011 012 013 014 Sym GBWP TON M SR degrees VDD = 5V Legend: TBD = To Be Determined (c) 2005 Microchip Technology Inc. DS21891B-page 23 PS200 TABLE 5-9: COMPARATOR SPECIFICATIONS (PINS LOOPFBK, CHGFBK, SHDN, VOVP) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +125C Min -- 0 -- +70* -- -- Typ 2 -- -- -- -- -- Max 5 VDD - 1.5 200* -- 20* 40* Units mV V nA dB ns ns Internal Output to pin Comments Comparator Specifications Param No. C01 C02 C03 C04 C05 * Note 1: Symbol VOS VCM ILC CMRR TRT Characteristics Input Offset Voltage Input Common Mode Voltage Input Leakage Current Common Mode Rejection Ratio Response Time(1) These parameters are characterized but not tested. Response time measured with one comparator input at (VDD - 1.5)/2, while the other input transitions from VSS to VDD - 1.5V. TABLE 5-10: COMPARATOR VOLTAGE REFERENCE (VREF) SPECIFICATIONS Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +125C Min -- -- -- -- -- -- Typ VDD/24* VDD/32 -- -- 2K* -- Max -- -- 1/4* 1/2* -- 10* Units LSb LSb LSb LSb s Comments Low Range (VRR = 1) High Range (VRR = 0) Low Range (VRR = 1) High Range (VRR = 0) Comparator Voltage Reference Specifications Param No. CV01 CV02 CV03 CV04 * Note 1: Symbol CVRES Characteristics Resolution Absolute Accuracy Unit Resistor Value (R) Settling Time (1) These parameters are characterized but not tested. Settling time measured while VRR = 1 and VR<3:0> transitions from 0000 to 1111. DS21891B-page 24 (c) 2005 Microchip Technology Inc. PS200 TABLE 5-11: Param No. A01 A02 A03 A04 A05 A06 A07 A10 A20 A20A A25 A30 Sym NR EABS EIL EDL EFS EOFF EGN -- VREF A/D CONVERTER CHARACTERISTICS Characteristic Resolution Total Absolute Error* Integral Error Differential Error Full-Scale Range Offset Error Gain Error Monotonicity Reference Voltage (1) Min -- -- -- -- 2.2* -- -- -- 2.2 2.5 (4) Typ -- -- -- -- -- -- -- guaranteed(2) -- Max 10 bits 1 1 1 5.5* 1 1 -- -- VDD + 0.3 VREF(5) 10 Units bit Conditions LSb VREF = 5.0V LSb VREF = 5.0V LSb No missing codes to 10 bits, VREF = 5.0V V LSb VREF = 5.0V LSb VREF = 5.0V -- V Absolute minimum to ensure 10-bit accuracy V k VSS VAIN VREF VAIN ZAIN Analog Input Voltage Recommended Impedance of Analog Voltage Source VREF Input Current*(3) VSS -- -- -- A50 IREF 10 -- 1000 A A -- -- 10 During VAIN acquisition. Based on differential of VHOLD to VAIN. During A/D conversion cycle. * These parameters are characterized but not tested. Data in `Typ' column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Total Absolute Error includes Integral, Differential, Offset and Gain Errors. 2: The A/D conversion result never decreases with an increase in the input voltage and has no missing codes. 3: VREF current is from external VREF or VDD pin, whichever is selected as reference input. 4: Only limited when VDD is at or below 2.5V. If VDD is above 2.5V, VREF is allowed to go as low as 1.0V. 5: Analog input voltages are allowed up to VDD, however, the conversion accuracy is limited to VSS to VREF. FIGURE 5-6: 134 Q4 A/D CLK A/D DATA ADRES ADIF GO SAMPLE A/D CONVERSION TIMING (NORMAL MODE) 1/2 TCY 131 130 9 8 OLD_DATA 7 6 3 2 1 0 NEW_DATA DONE 132 SAMPLING STOPPED Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. (c) 2005 Microchip Technology Inc. DS21891B-page 25 PS200 TABLE 5-12: Param No. 130* 130* Sym TAD TAD A/D CONVERSION REQUIREMENTS Characteristic A/D Clock Period A/D Internal RC Oscillator Period Conversion Time (not including acquisition time)(1) Acquisition Time Min 1.6 3.0* 3.0* 2.0* -- Typ -- -- 6.0 4.0 11 TAD Max -- -- 9.0* 6.0* -- Units s s s s TAD Conditions TOSC based, VREF 2.5V TOSC based, VREF full range ADCS<1:0> = 11 (RC mode) At VDD = 2.5V At VDD = 5.0V Set GO bit to new data in A/D Result register 131* TCNV 132* TACQ -- 5* 11.5 -- -- -- s s The minimum time is the amplifier settling time. This may be used if the "new" input voltage has not changed by more than 1 LSb (i.e., 1 mV @ 4.096V) from the last sampled voltage (as stated on CHOLD). If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. 134* TGO Q4 to A/D Clock Start -- TOSC/2 -- -- * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: ADRES register may be read on the following TCY cycle. FIGURE 5-7: 134 Q4 A/D CONVERSION TIMING (SLEEP MODE) 131 130 A/D CLK A/D DATA ADRES ADIF GO SAMPLE 132 SAMPLING STOPPED DONE 9 8 OLD_DATA 7 6 3 2 1 0 NEW_DATA Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. DS21891B-page 26 (c) 2005 Microchip Technology Inc. PS200 6.0 6.1 PACKAGING INFORMATION Package Marking Information 20-Lead PDIP XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX YYWWNNN Example PS200-I/P e3 0510017 20-Lead SOIC XXXXXXXXXXXXXX XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN Example PS200/SO e3 0510017 20-Lead SSOP XXXXXXXXXXX XXXXXXXXXXX YYWWNNN Example PS200/SS e3 0510017 Legend: XX...X Y YY WW NNN e3 * Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2005 Microchip Technology Inc. DS21891B-page 27 PS200 6.2 Package Details The following sections give the technical details of the packages. 20-Lead Plastic Dual In-line (P) - 300 mil Body (PDIP) E1 D 2 n E 1 A A2 c A1 eB Units Dimension Limits n p B INCHES* NOM 20 .100 .155 .130 B1 p MILLIMETERS NOM 20 2.54 3.56 3.94 2.92 3.30 0.38 7.49 7.87 6.10 6.35 26.04 26.24 3.05 3.30 0.20 0.29 1.40 1.52 0.36 0.46 7.87 9.40 5 10 5 10 L MIN MAX MIN MAX Number of Pins Pitch Top to Seating Plane A .140 .170 Molded Package Thickness A2 .115 .145 Base to Seating Plane A1 .015 Shoulder to Shoulder Width E .295 .310 .325 Molded Package Width E1 .240 .250 .260 Overall Length D 1.025 1.033 1.040 Tip to Seating Plane L .120 .130 .140 c Lead Thickness .008 .012 .015 Upper Lead Width B1 .055 .060 .065 Lower Lead Width B .014 .018 .022 Overall Row Spacing eB .310 .370 .430 Mold Draft Angle Top 5 10 15 Mold Draft Angle Bottom 5 10 15 * Controlling Parameter Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-019 4.32 3.68 8.26 6.60 26.42 3.56 0.38 1.65 0.56 10.92 15 15 DS21891B-page 28 (c) 2005 Microchip Technology Inc. PS200 20-Lead Plastic Small Outline (SO) - Wide, 300 mil Body (SOIC) E E1 p D 2 B n 1 h 45 c A A2 L A1 Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length Chamfer Distance Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic Units Dimension Limits n p A A2 A1 E E1 D h L c B MIN .093 .088 .004 .394 .291 .496 .010 .016 0 .009 .014 0 0 INCHES* NOM 20 .050 .099 .091 .008 .407 .295 .504 .020 .033 4 .011 .017 12 12 MAX MIN .104 .094 .012 .420 .299 .512 .029 .050 8 .013 .020 15 15 MILLIMETERS NOM 20 1.27 2.36 2.50 2.24 2.31 0.10 0.20 10.01 10.34 7.39 7.49 12.60 12.80 0.25 0.50 0.41 0.84 0 4 0.23 0.28 0.36 0.42 0 12 0 12 MAX 2.64 2.39 0.30 10.67 7.59 13.00 0.74 1.27 8 0.33 0.51 15 15 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-013 Drawing No. C04-094 (c) 2005 Microchip Technology Inc. DS21891B-page 29 PS200 20-Lead Plastic Shrink Small Outline (SS) - 209 mil Body, 5.30 mm (SSOP) E E1 p D B n 2 1 c A A2 f L A1 Number of Pins Pitch Overall Height A .079 Molded Package Thickness A2 .065 .073 Standoff A1 .002 Overall Width E .291 .323 Molded Package Width E1 .197 .220 Overall Length D .272 .289 Foot Length L .022 .037 c Lead Thickness .004 .010 f Foot Angle 0 8 Lead Width B .009 .015 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MO-150 Drawing No. C04-072 Units Dimension Limits n p MIN INCHES NOM 20 .026 .069 .307 .209 .283 .030 4 - MAX MIN MILLIMETERS* NOM 20 0.65 1.65 1.75 0.05 7.40 7.80 5.00 5.30 .295 7.20 0.55 0.75 0.09 0 4 0.22 - MAX 2.00 1.85 8.20 5.60 7.50 0.95 0.25 8 0.38 Revised 11/03/03 DS21891B-page 30 (c) 2005 Microchip Technology Inc. PS200 THE MICROCHIP WEB SITE Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: * * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com In addition, there is a Development Systems Information Line which lists the latest versions of Microchip's development systems software products. This line also provides information on how customers can receive currently available upgrade kits. The Development numbers are: Systems Information Line CUSTOMER CHANGE NOTIFICATION SERVICE Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. 1-800-755-2345 - United States and most of Canada 1-480-792-7302 - Other International Locations (c) 2005 Microchip Technology Inc. DS21891B-page 31 PS200 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. To: RE: Technical Publications Manager Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Device: PS200 Questions: 1. What are the best features of this document? Y N Literature Number: DS21891B FAX: (______) _________ - _________ 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS21891B-page 32 (c) 2005 Microchip Technology Inc. PS200 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device X Temperature Range /XX Package XXX Pattern Examples: a) b) Device PS200 c) PS200-I/SO = Industrial Temperature, SOIC package PS200-I/SS = Industrial Temperature, SSOP package PS200-I/P = Industrial Temperature, PDIP package Temperature Range I = -20C to +85C (Industrial) Package P SO SS = = = PDIP SOIC SSOP (c) 2005 Microchip Technology Inc. DS21891B-page 33 WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Atlanta Alpharetta, GA Tel: 770-640-0034 Fax: 770-640-0307 Boston Westford, MA Tel: 978-692-3848 Fax: 978-692-3821 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 San Jose Mountain View, CA Tel: 650-215-1444 Fax: 650-961-0286 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 ASIA/PACIFIC Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8676-6200 Fax: 86-28-8676-6599 China - Fuzhou Tel: 86-591-8750-3506 Fax: 86-591-8750-3521 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 China - Shunde Tel: 86-757-2839-5507 Fax: 86-757-2839-5571 China - Qingdao Tel: 86-532-502-7355 Fax: 86-532-502-7205 ASIA/PACIFIC India - Bangalore Tel: 91-80-2229-0061 Fax: 91-80-2229-0062 India - New Delhi Tel: 91-11-5160-8631 Fax: 91-11-5160-8632 Japan - Kanagawa Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Taiwan - Hsinchu Tel: 886-3-572-9526 Fax: 886-3-572-6459 EUROPE Austria - Weis Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark - Ballerup Tel: 45-4450-2828 Fax: 45-4485-2829 France - Massy Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Ismaning Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 England - Berkshire Tel: 44-118-921-5869 Fax: 44-118-921-5820 10/20/04 DS21891B-page 34 (c) 2005 Microchip Technology Inc. |
Price & Availability of PS200
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |